Mirage S Coupe MIVEC powered

The plan is to have 1.6 liter Mivec engine in this mirage with suspensions chassis ready for my amateur street racing

Actually finally i found engine then Putra(Proton 418 Coupe Putra Passenger etc.) but it has tons of issues with glasses

Forums link's of this build all info is same just lower amount of pictures:

Mirage S 4G92 MIVEC for Motorsport - mirageforums.net

First plan was to restore and work on this model

While i was searching for glasses the Mirage S came in

so finally after all CA4A colts Putra's i found this Mirage S

This is from advert what i found:

But once this one found will go on to this one

Look of exhaust

moving on to the engine:

problem is that i got this Mivec with loom and Mine's tunned ecu is remade to 1.8 will have to downgrade it to 1.6

if you aske me why: answer is on my street races there is "up to 1600cm3 " class/division and next one is "up to 2000cm3" so i don't want to fight hondas k20 (260HP) with 1.8 liter so 1.6 is good decision and engine from factory is more powerful then honda d16 b16 etc.

so this is MIVEC i found:

Owner of this engine parted out his car i ordered only engine without exhaust as it's against my street racing rules it has to be OEM

as the engine came in i took off the valve cover to see if it's has everything inside

yes it might be that it's "black top mivec" but not sure

and yes the ecu has MINE's tuned eprom on it hoping that it will run with it nicely

MIVEC ecu gen1	ECU	Eprom

After some time i decided that i need new pistons as the 1.8 ones will not fit on my 4g92 DOCH engine so ordered new ones from Malysia:

Toto pistons +1.00

Toto pistons

Found MIVEC covers and ordered them to have nice look under hood

once they arrived

Engine owner had Exedy 4punch clutch set even it's used it will work perfectly for my street racing

Exedy G21578

he he 10k rpm cluster is on his way

i was told that it just spins in mph but speed is in km/h

thinking of redoing that side of speed to EU one as there is mo maximum speed as i think i might achieve 200+kmh

once arrived and works added it to other Colt of mine for testing and see how it goes

10 rpm cluster Colt CA 4G61 N/A engine

in final what I've done is added km/h to it

so here is 10r/rpm cluster with 240km/h speed scale

works fine just slow in showing speed, but will fix that later

Eclipse 2G GST rear win on mirage

Mitsubishi Mirage S coupe with 2G eclipse GST/GSX rear trunk wing just for fun

just for fun added GST wing on trunk of mirage and thinking of remaking one to fit the trunk from some sides looks good need to work on that later as it does not look that good from sides

Started to work on engine:

4G92 block re drill to +1.00 for toto pistons

Once all this job was done worked on pistons to get then ceramic coating covered and assembled.

		4G92 DOHC MIVEC Pistons and Rods assembled

Got all new racing bearing and assembled cylinder block with crankshaft pistons

Assembling Block with Crankshaft

King Racing MB5176XP Main bearings to 4G92	MB5176XP main bearing other side of it	King Racing MB5176XP main bearings installed
King Racing MB5176XP main bearing in place	4G92 assembly works with Permatex Ultra Slick lube	Permatex Ultra Slick lube used
4G92 Block with Crankshaft installed	King Racing MB5176XP bearing other side	4G92 Main bearing MB5176XP King Racing installed
4G92 Main bearings MB5176XP King Racing installed	King Racing MB5176XP main bearing installed 4G92 Block	4G92 cylinder block with crankshaft installed

Once crankshaft is installed will have to check NM torques to tighten bolts as per factory requirements

Pages from 4G9x engine manual with bolts/nuts torques

	4G92 torques-2	4G92 torques-3
4G92 torques-4	4G92 torques-5